首页 > 消息 > 行业新闻 > How can the diamond cutter segment be sharper? How to maintain?
联系我们
联系方式: 福建省南安博威机械有限公司,地址:福建省泉州市南安水头镇 邮编:362342 电话:(+ 86)595-86990206 传真:(+ ...
现在联系
跟着我们
最新消息
  • 钻石的物理性质

    钻石是最大的矿物硬度之一。钻石根据天然和人造的原因可分为两类。天然的...
  • 超薄锯片底座的厚度是多少?

    超薄金刚石锯片是指高精度专用金刚石切割片,根据粘接剂的不同,产品分为金属粘接剂,树脂粘接剂和电镀金刚石切割片。
  • 什么是Lavina快速更换金刚石混凝土研磨刀头?

    说明: 什么是Lavina快速更换金刚石混凝土研磨刀头? 我们的 Lavina金刚石研磨刀头 主要用于研磨混凝土,也可用于研磨石材表面。我们采用工业级金...
  • 钎焊工艺的简介

    钎焊是采用比母材熔点低的金属材料作钎料,将焊件和钎料加热到高于钎料熔点,低于母材熔化温度,利用液态钎料润湿母材,填充接头间隙并与母材相互...
  • 树脂的定义

    树脂通常是指受热后有软化或熔融范围,软化时在外力作用下有流动倾向,常温下是固态、半固态,有时也可以是液态的有机聚合物。广义地讲,可以作为...
  • 为什么金刚石刀片无法加工钢?

    高于800摄氏度时,金刚石粉末溶解在铁中。使用金刚石切削工具车削铁质材料,由于摩擦热,直径大,直径大,尺寸大,尺寸大等缺点。
  • 锯片可以切割玉吗?

    它广泛用于切割宝石,石材和硬质材料,如玻璃,陶瓷和石墨。
  • 可以在混凝土中使用125mm衬套锤板吗?

    衬套锤板可以去除旧的环氧涂层,翻新不同种类的地面,并进行古董效果。有效和安全的防滑花岗岩,花岗岩,大理石和混凝土表面。铺设新层之前混凝土研磨和抛光的制备。
  • 金刚石段的生产技术?

    BOREWAY级机械金刚石段的制造过程分为5个步骤,分别是配料,混合,冷压,热压...
  • 如何为金刚石碗磨轮选择合适的粒度?

    描述: 如何选择为 金刚石碗磨轮选择合适的粒度? 金刚石碗磨轮 金属结合剂金刚石具有高强度,优异的耐磨性和低摩擦系数。 金刚石碗磨轮 ...

消息

How can the diamond cutter segment be sharper? How to maintain?

Dora Zhang 2020-06-09 18:01:14
Most diamond tools are composed of a base body and a cutter head, whether it is a saw blade, a bowl grinding, a grinding block, a drill, etc.
This time the bowl mill talks about the blade of the saw blade, there are cutting blocks, stone slab, concrete, granite , Marble and other materials, how to become sharp when used?

The blade is sharp and durable ,There are some contradictions, if the carcass is more resistant to wear, the blade will not be sharp, the carcass formula, sintering process , Diamond strength, etc. will affect the sharpness of the diamond bit, if it is relatively copper-based, adding some fine materials into the diamond will also add sharpness.

This diamond has been developed as a raw material for many products for many years. When it can be synthesized through a certain temperature and pressure, this cutting tool has entered a period represented by superhard materials.

If the cutter head is used improperly, it will affect the service life and thus affect the working efficiency. So how should bowl mills be sold to maintain diamond cutter heads?

Diamond tool bit maintenance:

The spalling of the diamond coating can prevent the spalling of the coating. It is a serious problem of diamond-coated cutter heads, and it is also a common problem (especially when processing materials such as carbon fiber), which will cause the tool life to be difficult to predict.

In the late 1990s, the interface chemical properties were determined to be important factors affecting the adhesion properties of diamond coatings. By selecting the chemical characteristics of the cemented carbide with good compatibility, using appropriate pretreatment technology and reasonable deposition reaction conditions.

It is possible to reduce or eliminate the peeling of the diamond coating, and realize a stable wear pattern stably. Observing a diamond-coated tool with normal wear under a microscope, it can be found that the diamond is steadily worn up to the cemented carbide substrate without chipping or flaking.

The main advantages of this diamond tool: the hardness can reach 8000HV, which is 80 to 120 times that of cemented carbide. The thermal conductivity is 700W/mk, which is 1.5 to 9 times that of cemented carbide, even higher than PCBN and copper, so PCD tool heat transfer is rapid. The friction coefficient is generally only 0.1 to 0.3 (the friction coefficient of cemented carbide is 0.4 to 1), so this tool can significantly reduce the cutting force.